Lippert 2x2 Through-Frame Slide-Out Parts Diagram & Gear Reference

Identify Lippert 2×2 electric through-frame slide-out wear tabs, gears, gear-pack components and stop hardware using the factory A–G reference list and real NewRVParts product photographs. The manufacturer supplies separate drawings for center-drive and actuator-equipped through-frame configurations; this guide is limited to the 2×2 component family.

Critical identification: A 2×2 through-frame system is different from 2×3, 2.5×2.5 and Schwintek In-Wall slide-outs. Confirm the original gear tooth count, pitch angle, arm dimensions, manufactured version, actuator type and drive arrangement. Do not order from appearance or RV make alone.

Lippert 2×2 factory diagrams: system and individual parts

Start with the complete slide mechanism, then use the A–G component drawing to identify the gear pack, spur gears, roller shaft, stop can, wear tab or rear roller. The assembly example shows an actuator-equipped configuration; center-drive units have a different drive arrangement.

Lippert 2 by 2 electric through-frame slide-out with actuator: manufacturer assembly drawing showing motor, actuator, cross shafts, inner and outer arms, gear pack and wear tabs
2×2 assembly with actuator: identifies motor, actuator, cross shaft, room bar, inner and outer arms, and wear components. View full-size drawing.
Lippert 2 by 2 electric through-frame slide-out factory A–G parts diagram: 281331 gear pack, 101941 15-tooth gear, 122739 18-tooth gear, 105893 roller shaft, 122840 stop can, 103480 wear tab and 104475 rear roller
2×2 components A–G: part drawings and manufacturer numbers to compare with the replacement-product photos below. View full-size drawing.

Quick guide to the 2×2 component groups

Slide room support and room bar
Inner armF wear tabs
G rear roller
2×2 slide mechanismA gear pack
B / C alternate gears
D roller shaft
Outer armE stop can
Actuator or center drive
A · Gear packB · 15T gearC · 18T gearD · ShaftE · Stop canF · Wear tabG · Rear roller

The A–G labels correspond to Lippert's parts chart. Refer to the factory service instructions for exact dimensions and installation steps.

Replacement-part photographs and numbers

The photos below show the replacement parts identified in the factory A–G drawing. Select a photo for the matching product listing. If replacing gear pack 281331, confirm the installed gear configuration; older Lippert material and newer part specifications are not fully consistent about the tooth count.

A · 281331Lippert 281331 2×2 15-tooth gear-pack assembly2×2 gear-pack assembly — check installed gearShop exact manufacturer number; verify installed gear count B · 700612Lippert 700612 15-tooth spur gear; supersedes factory drawing 10194115-tooth spur gear; supersedes factory drawing 101941View matching NewRVParts listing C · 122739Lippert 122739 18-tooth spur gear18-tooth spur gearView matching NewRVParts listing E · 122840Lippert 122840 Steel stop canSteel stop canView matching NewRVParts listing F · 103480Lippert 103480 Black plastic wear tabBlack plastic wear tabView matching NewRVParts listing

Lippert A–G parts cross-reference

Factory callout Manufacturer reference Component Verify
A 281331 2×2 gear-pack assembly 15-tooth gear-pack assembly without roll pins. Check the installed gear configuration before ordering.
B 101941 → 700612 15-tooth spur gear Current manufacturer replacement part is 700612.
C 122739 18-tooth spur gear Distinct gear specification, not a substitute for the 15-tooth gear.
D 105893 Roller shaft Factory component reference.
E 122840 Slide-out stop can Match through-frame actuator and stop hardware.
F 103480 Plastic wear tab Early and current tab shapes are shown in factory documentation.
G 104475 Rear roller Factory component reference.
Gear identification alert: Lippert's current #281331 product document specifies a 15-tooth gear-pack assembly, no roll pins, while an older Lippert catalog table describes #281331 as 18-tooth. Part 281331 is the complete 15-tooth assembly without roll pins. Confirm the installed 2×2 gear type before purchase. The separate 18-tooth spur gear is #122739. Lippert now lists #700612 as a replacement for earlier 15-tooth gear #101941. Do not infer compatibility from the model year without inspecting the installed mechanism.

View official exploded drawings and service manuals

Lippert 2×2 Electric Slide System — factory assembly and A–G component diagrams. The technical resource also provides gear-pack replacement instructions, actuator identification, maintenance manuals and the 14.5° versus 20° gear comparisons. Use Lippert's factory documentation for exact component placement, gear comparisons and repair procedures.

Related NewRVParts collections

RV Slide-Out Parts & Accessories · Lippert Components · New RV Parts

Also see the Schwintek In-Wall slide-out guide for the different in-wall motor-and-rail mechanism.

Primary sources: Lippert's 2×2 Electric Slide System support components image CCD-0002560; Lippert current 281331, 700612, 122739 and 103480 product specifications. Refer to Lippert's factory diagrams for the original assembly positions. Consult a qualified technician for slide-out gear, room support or actuator work.

Save on Parts & Accessories

Sign up for special offers, new product updates, and deals on RV, truck camper, towing, truck, and marine parts and accessories.

About NewRVParts

NewRVParts is an online-only source for brand-new RV parts and accessories, truck camper equipment, towing and trailer parts, truck accessories, and marine products. We serve customers throughout Canada and the United States, with products from trusted manufacturers shipped through a large North American distribution network. Shop online for replacement parts, equipment, and accessories delivered directly to your door.

Shop RV Parts