Barker's VIP 3000 electric tongue jack raises or lowers the trailer tongue with a 3,000 lb lifting capacity and an 18-inch travel range. Its exploded diagram makes it easier to identify the motor, reduction gear, torque limiter, protective covers, foot pad and manual crank without confusing these pieces with the heavier VIP 3500 assemblies.
Barker VIP 3000 original exploded parts drawing
Open the manufacturer's own page-three drawing to see the numbered pieces of the complete powerhead, gear drive and jack post. The manual also includes the 12-volt installation and operation instructions.
Original parts by numbered callout
Find a callout in Barker's diagram and match its factory part number below. Parts that are not linked are provided to help identify the original assembly; the store listings shown farther down are complete jacks.
| Callout | Barker number | Part identification |
|---|---|---|
| 1 | 613-0000 | Pair of #10-32 acorn nuts |
| 2 | 27344 | White motor sleeve |
| 2 | 27276 | Black motor sleeve |
| 3 | 30783 | White base casting |
| 3 | 30782 | Black base casting |
| 4 | 606-0010 | Zinc-finished cover fastener |
| 4 | 606-0008 | Black-head cover fastener |
| 5 | 16392 | Cable ties, pair |
| 6 | 27338 | White machined cover |
| 6 | 27259 | Black machined cover |
| 7 | 27274 | Motor sealing ring |
| 8 | 611-2100 | Hex locknuts |
| 9 | 736-2300 | Lift/lower toggle switch |
| 10 | 16263 | 3000-series jack motor |
| 11 | 30331 | White cap assembly |
| 11 | 30330 | Black cap assembly |
| 12 | 30835 | Head-cover decal |
| 13 | 30683 | White lock-position indicator |
| 13 | 30341 | Black lock-position indicator |
| 14 | 16434 | Hole plugs |
| 15 | 623-1216 | Groove pin in drive post |
| 16 | 619-0003 | Internal-tooth mounting lockwashers |
| 17 | 608-0006 | Powerhead set screws |
| 18 | 621-0004 | Drive dowel pins |
| 19 | 17808 | Wire retaining clamp |
| 20 | 736-0008 | Night-light toggle switch |
| 21 | 29880 | Electrical connector and fuse holder |
| 22 | 645-0024 | Flanged bushing |
| 23 | 618-1002 | Half-inch lockwasher |
| 24 | 600-0011 | Half-inch foot-plate bolt |
| 25 | 634-0028 | Retaining rings |
| 26 | 30839 | VIP 3000 torque-limiter assembly |
| 27 | 641-0009 | Drive bushing |
| 28 | 29306 | Gear-cover gasket |
| 29 | 80501 | Gear-housing bushings |
| 30 | 80208 | Spacing washer |
| 31 | 28207 | Gear-drive assembly |
| 32 | 17419 | Machined gear-cover casting |
| 32 | 30774 | Black finished gear cover |
| 33 | 27257 | Black lead-wire assembly |
| 34 | 605-0012 | Gear-cover screws |
| 35 | 26236 | Cable-entry rubber grommet |
| 36 | 27335 | Black post assembly |
| 36 | 31840 | Black altered-flange post assembly |
| 37 | 21349 | Round jack foot plate |
| 38 | 618-1009 | Motor stud lockwashers |
| 39 | 617-0071 | M5 motor stud washers |
| 40 | 30850 | Motor mounting studs |
| 41 | 30313 | Night-light lens gasket |
| 42 | 27262 | Night-light lens |
| 43 | 606-5001 | Lamp-lens retaining screws |
| 44 | 27253 | Lamp electrical lead |
| 45 | 10017 | Post adapter |
| 46 | 28259 | Emergency manual crank handle |
Photos of complete Barker power jacks
Use these NewRVParts catalog photos to compare the model and finish with your installed jack. The internal repair components in the diagram are separate from the complete products pictured.
Confirm the exact jack before selecting a part
This Barker drawing covers VIP 3000 white model 30826 and black model 32453. The housing finish, cap and selected fasteners have separate part numbers; match the original model and finish before replacing cosmetic or structural pieces. The 2011 drawing supersedes some part numbers in the older VIP 3000 manual.
The VIP 3000 motor is Barker part 16263, and its torque limiter is 30839. The VIP 3500 uses a different motor and torque limiter. The lift toggle appears as 736-2300 in the manufacturer drawing, but its exact service configuration should be checked against the installed switch and connectors.
For related models, see the Barker VIP 3500 Power Tongue Jack Exploded Parts Diagram.