The Barker 24130 Auto-Drain converts a compatible 3-inch Valterra or Bristol manual waste gate to motor operation without removing the existing valve. Its factory exploded drawing identifies the actuator's rack gear, mounting bracket, motor box and electrical switch components separately.

Barker original numbered exploded parts drawing and wiring

Open the manufacturer's PDF to enlarge the drawing and read the original hardware, model and component information.

Open the original Barker PDF for a zoomable view of the components.

Open manufacturer exploded parts drawing (PDF)

View bracket clearances and electrical wiring (PDF)

Original component numbers by diagram callout

The table lists original Barker references for identification. Unlinked items are not presented as available replacement products.

Callout / category Barker number Component
1 31473 Machined 3-inch base
2 24131 3-inch rack gear
4 25012 3-inch Auto-Drain label
5 25366 3-inch warning/serial label
3 26876 Machined cover
6 24134 Drive gear
7 24122 Motor box assembly
8 30992 Spacer
9 610-0006 5/16-20 hex nut
10 30993 Universal mounting bracket
11 605-0007 #4-24 machine screws (four)
12 601-1006 #10-32 by 1.12-inch screws (two)
13 80225 Washer
14 611-2100 #10-32 locknuts (two)
15 634-1250 E-ring
16 24749 Drive shaft
17 30376 Cams (two)
18 738-0055 Microswitch
19 602-0002 #4-40 screws (two)
20 80209 Mounting washers (two)
21 31478 Connector assembly
22 12819 Strain relief
23 31471 Rocker-switch box
24 606-0002 #6 screws
25 738-0007 Rocker switch
26 31479 Switch-box lamp assembly
27 600-0077 Hex bolt
28 27129 Patent label
29 28429 Plate support
30 23087 Box label
31 25476 Warning label
32 31477 Male connector assembly
33 31855 In-line fuse assembly
34 31472 Switch-box assembly, as labelled in 3-inch drawing
35 31472 Complete switch-box assembly
36 17311 Strain relief
37 743-0016 Wire strain relief
38 742-0051 Terminals (two)
39 23136 24-inch black wire
40 23137 24-inch white wire
Not drawn 24006 Switch-box cover

NewRVParts product photographs

The following photos identify complete Barker units currently listed on NewRVParts. Interior components may be separate service items.

Confirm the original model

The 3-inch assembly uses Barker base 31473, rack gear 24131 and Auto-Drain label 25012. Do not substitute the 1½-inch base 31919 or rack gear 24136. Barker's installation drawing shows which universal-bracket holes are used for the larger valve.

Install the universal bracket using two existing valve-flange bolts, then set the manufacturer-required 1/8–3/16-inch clearance between spacer and rack gear with the valve fully closed. The supplied wiring illustration uses a 12V supply and a 1/2-amp slow-blow fuse. Disconnect power before servicing, and empty the holding tank before initial installation as Barker recommends.

Save on Parts & Accessories

Sign up for special offers, new product updates, and deals on RV, truck camper, towing, truck, and marine parts and accessories.

About NewRVParts

NewRVParts is an online-only source for brand-new RV parts and accessories, truck camper equipment, towing and trailer parts, truck accessories, and marine products. We serve customers throughout Canada and the United States, with products from trusted manufacturers shipped through a large North American distribution network. Shop online for replacement parts, equipment, and accessories delivered directly to your door.

Shop RV Parts