Lippert 2x3 Electric Through-Frame Slide-Out Parts Diagram

This illustrated parts reference identifies the gear-pack and slide room hardware used in Lippert 2×3 electric through-frame slide-out systems. The A–L factory references follow Lippert's original illustrated service list. Parts with matching manufacturer numbers link to their NewRVParts listings. Other references help identify the original installed mechanism.

Identify the mechanism first: A 2×3 electric through-frame assembly is not the same as 2×2, 2.5×2.5, hydraulic or Schwintek In-Wall mechanisms. Check the slide-arm measurements, original gear type, original part label and actuator before ordering. Confirm the system is 2×3 electric rather than the 2×3 hydraulic version.

Lippert 2×3 factory slide-out assembly illustration

This manufacturer drawing shows the two outer and inner slide arms, motor, external gearbox, rear roller, roller shaft and spur gear in position. Use the A–L parts list below to identify service components; the mechanism drawing is not a complete replacement-parts bill of materials.

Lippert 2 by 3 electric through-frame RV slide-out factory assembly drawing showing inner and outer arms, reduction gearbox, motor, rear roller, roller shaft and spur gear
2×3 electric assembly: motor and gearbox sit outside the slide arms; the section view identifies the roller and spur-gear area. The 2×2 and 2.5×2.5 mechanisms are covered in separate guides. View full-size drawing.

2×3 parts identification by assembly group

K — Outer armH rear stop bracket; room mounting structure
A — Gear-pack areaB wear pads · C rear roller · D 18T gear or E 15T gear
D = 18 teeth / 14.5°E = 15 teeth / 20°
L — Inner armF front stop bracket; G wear bar plate

This guide groups the factory A–L part references. The 15-tooth and 18-tooth spur gears have different pitch and pressure angles; they are alternatives for different configurations, not a matched pair.

Replacement-part photographs

The five product photographs below link to matching part-number listings. The controller and switch are optional system-dependent components, so compare the existing wiring and control labels before ordering.

D · 122739Lippert 122739 18-tooth spur gear, 14.5° pressure angle12273918-tooth spur gear, 14.5° pressure angle E · 700612Lippert 700612 15-tooth spur gear; manufacturer replacement for historic 10194170061215-tooth spur gear; manufacturer replacement for historic 101941 B · 103480Lippert 103480 Black wear tab / original-current styles103480Black wear tab / original-current styles Electrical · 135666Lippert 135666 Slide-out control module / controller 10665135666Slide-out control module / controller 10665 Switch · 117461Lippert 117461 White slide-out rocker switch and panel117461White slide-out rocker switch and panel

Factory A–L parts breakdown

Factory reference Lippert number Component Check
A 140409 2×3 gear pack assembly Component identification reference
B 103480 Wear pad; original and current profiles Linked product below; compare installed wear-tab profile
C 104474 Rear roller Component identification reference
D 122739 18-tooth spur gear, 14.5° pressure angle Linked exact part; do not replace with 15-tooth variant
E 101941 → 700612 15-tooth spur gear, 20° pressure angle 700612 is current manufacturer-number replacement for the historic 101941; confirm installed type
F 125699 Front stop bracket Part number shown for identification
G 115375 Wear bar plate, 3×1 Part number shown for identification
H 105790 Rear stop bracket Part number shown for identification
I 115251 Main room head with hardware Part number shown for identification
J 116045 Kitchen room head with hardware Part number shown for identification
K 157654 Outer arm assembly Part number shown for identification
L 157653 Inner arm assembly Part number shown for identification
Do not mix gear types: Original factory drawing lists D as 122739, 18-tooth and 14.5° pressure angle; E as 101941, 15-tooth and 20°. Lippert separately identifies current part 700612 as a replacement for 101941. Verify the actual mechanism before using that replacement. A 2×2 gear pack such as 281331 is not a 2×3 gear-pack substitute.

Manufacturer service illustrations

Lippert 2×3 Electric Slide System drawings and service manuals · Lippert original component illustrations (PDF, 2×3 section). Manufacturer drawings are linked for technical identification and not reproduced.

Related NewRVParts collections and guides

RV Slide-Out Parts & Accessories · Lippert Components · Separate 2×2 through-frame guide · Separate Schwintek guide

Primary factory reference: Lippert Electric Through Frame Slide-Out Owner's Manual CCD-0001613, July 13, 2018, 2×3 Electric Through Frame Slide-Out Components (pp. 24–29). Current manufacturer part-number references and the NewRVParts catalog were cross-checked for linked items. Follow manufacturer safety instructions for moving room assemblies and drive mechanisms.

Save on Parts & Accessories

Sign up for special offers, new product updates, and deals on RV, truck camper, towing, truck, and marine parts and accessories.

About NewRVParts

NewRVParts is an online-only source for brand-new RV parts and accessories, truck camper equipment, towing and trailer parts, truck accessories, and marine products. We serve customers throughout Canada and the United States, with products from trusted manufacturers shipped through a large North American distribution network. Shop online for replacement parts, equipment, and accessories delivered directly to your door.

Shop RV Parts