BAL 23025 & 23026 Light Trailer Stabilizer Parts Diagram and Crank Guide

BAL 23025 and 23026 light-trailer stabilizers are compact folding corner jacks for compatible pop-up campers, teardrop and lightweight travel trailers. Compare boxed stabilizer pairs, individual replacement jacks, slotted crank handles, footpads and braces using BAL's model and mounting drawings.

Current model identification: 23025 is a 17-inch boxed pair using single jack 23005 (20300442). 23026 is the 20-inch boxed pair using single 23007 (20300443). Both are rated at 1,000 lb static load per jack, with about 2-inch stored height. These stabilizers are not lifting jacks or tire-service supports.

BAL stabilizer model and component illustrations

Factory model identification: 23025/23005 (17 inches) vs 23026/23007 (20 inches)
Factory model identification: 23025/23005 (17 inches) vs 23026/23007 (20 inches).

Original BAL RV Products factory reference, displayed from the manufacturer's document library. Cross-check the component numbers with the table below.

Open the original factory drawing in a new tab.
Show supplementary simplified diagram (not the factory drawing)
BAL light trailer 23025 and 23026 stabilizer and service accessory locator Original editorial schematic of the jack mounting channel, folding arms, drive screw, removable slotted crank and optional footpad. Editorial callout numbers match the parts table and do not indicate OEM exploded diagram positions. 1 / 3 · boxed jacks5–7 · cranks 8 · 23035optional round pad 9 · Lock-Armoptional frame brace Conceptual locator, not a manufacturer exploded diagram or installation drawing
The numbered overview helps locate each component. Refer to BAL's factory model-identification and mounting drawings for the correct jack size and installation positions.

Boxed pair versus single jack

BAL kit Single replacement Kit contents Fitment check
23025 · 17 in 23005 / 20300442 Two jacks, 23033 crank, six Tek screws, six star washers, instructions Manufacturer's 17-inch 23025 family
23026 · 20 in 23007 / 20300443 Two jacks, 23033 crank, six Tek screws, six star washers, instructions 20-inch family; check the actual frame-to-ground clearance and mount points

Stabilizer jacks, cranks and accessories

Compare the available boxed jack sets, individual replacements, crank handles and accessories below. Select a photograph to see product details and included components.

BAL 23026 20-inch boxed pair with crankBAL 2302620-inch boxed pair with crankView exact matching productBAL 23007 20-inch single replacement jackBAL 2300720-inch single replacement jackView exact matching productBAL 23031 Optional slotted speed crankBAL 23031Optional slotted speed crankView exact matching productBAL 23032 Short slotted crank, 6-inch reachBAL 23032Short slotted crank, 6-inch reachView exact matching productBAL 23033 Boxed-system slotted crank, 14-inch reachBAL 23033Boxed-system slotted crank, 14-inch reachView exact matching productBAL 23035 Four 6-inch round footpads with mounting hardwareBAL 23035Four 6-inch round footpads with mounting hardwareView exact matching productBAL 23216 Optional pair of Lock-Arm bracesBAL 23216Optional pair of Lock-Arm bracesView exact matching product

Numbered manufacturer-part identification table

Key Number Component Ordering check
1 23025 17-inch light-trailer boxed pair Two jacks, 23033 crank, installation hardware; exact 23025 product not found
2 23005 / 20300442 17-inch single jack replacement Component identification reference
3 23026 20-inch light-trailer boxed pair Two jacks, standard 23033 crank, installation hardware
4 23007 Single 20-inch jack Also OEM number 20300443; no crank or hardware supplied
5 23033 Standard slotted-drive crank 14-inch shaft; supplied with boxed kits
6 23031 Slotted speed crank Optional manual handle for both boxed models
7 23032 Short slotted crank 6-inch shaft; verify adequate installed hand access
8 23035 Set of four round footpads 6-inch diameter pads; maker confirms 23025/23026 and singles
9 23216 Lock-Arm stabilizer braces Optional add-on; confirm frame attachment and leg geometry

Crank differences and optional foot pads

23033 is BAL's standard boxed-set slotted crank with a 14-inch shaft reach. 23031 is the optional slotted-end speed-handle upgrade, while 23032 is the shorter 6-inch slotted crank. These differ from the ¾-inch hex cranks used on BAL's larger scissor-jack and C-Jack sets; check the original drive slot and hand clearance.

23035 contains four 6-inch round footpads with bolts and rubber anti-rattle sleeves. BAL confirms fitment for 23025/23005 and 23026/23007. Footpads increase ground-contact area, not rated jack capacity. 23216 is an optional telescoping brace kit listed in BAL's accessory literature; verify frame attachment and stabilizer geometry before adding it.

Mounting-hole dimensions and model identification

Factory hole-position chart: 3 in A / 16.171 in B
Factory hole-position chart: 3 in A / 16.171 in B.

Original BAL RV Products factory reference, displayed from the manufacturer's document library. Use the manufacturer's measurement chart; do not use a screen image as a drilling template.

Open the original factory drawing in a new tab.
Show supplementary simplified diagram (not the factory drawing)
BAL stabilizer jack 23025 and 23026 mounting-hole dimensions Original schematic of maker's mounting centers with dimension A 3 inches across wide front mounting bracket and dimension B 16.171 inches along body for both 23025 and 23026 jacks. A: 3 inB: 16.171 inHole spacing for both 23025 and 23026Editorial schematic. Use the original BAL print, not this drawing, for accurate mounting dimensions and drilling.
Simplified mounting overview based on BAL's mounting-hole diagram, which shows A = 3 inches and B = 16.171 inches for both families. Not a drilling template.
Replacing an older stabilizer: BAL currently identifies model 23026 / 23007 as the 20-inch family. Compare the original model number, frame-to-ground clearance and mounting-hole positions before ordering. Follow the installation instructions for your particular trailer and jack version.

BAL mounting diagrams and installation instructions

BAL 17-in versus 20-in identification photos BAL factory mounting-hole diagram BAL installation/operation manual (PDF) BAL current model-family technical listing

Use BAL's installation drawings to check the frame and crossmember mounting points. These stabilizers are not intended to lift or support a trailer during wheel or axle service. Follow BAL's crank and power-tool instructions.

Related NewRVParts jack references

BAL manual C-Jacks (19–31 in)BAL Classic/Deluxe/LoPro scissor jacksJacks & LevelingJack and awning diagram index

Save on Parts & Accessories

Sign up for special offers, new product updates, and deals on RV, truck camper, towing, truck, and marine parts and accessories.

About NewRVParts

NewRVParts is an online-only source for brand-new RV parts and accessories, truck camper equipment, towing and trailer parts, truck accessories, and marine products. We serve customers throughout Canada and the United States, with products from trusted manufacturers shipped through a large North American distribution network. Shop online for replacement parts, equipment, and accessories delivered directly to your door.

Shop RV Parts