JR Products GSNI-5200 17-Inch Gas Spring Force & Size Guide

JR Products' GSNI-5200 gas springs are 17 inches long when fully extended, with plastic ball-socket ends and a black nitride shaft. Five force ratings share the same dimensions, from 30 to 75 lb. This guide helps you match the original spring for an RV compartment door, trailer hatch or similar hinged application.

Compare the available force ratings

All listed GSNI-5200 models share 17-inch extended length, 9.66-inch compressed length, 7.34-inch stroke, a 6 mm rod and 15 mm tube. The difference between these exact part numbers is their listed push force.

17 inFully extended length
9.66 inFully compressed length
7.34 inGas spring stroke
Manufacturer MPN Push force Extended Compressed Stroke End fitting
GSNI-5200-30 30 lb 17 in 9.66 in 7.34 in Plastic ball sockets
GSNI-5200-40 40 lb 17 in 9.66 in 7.34 in Plastic ball sockets
GSNI-5200-50 50 lb 17 in 9.66 in 7.34 in Plastic ball sockets
GSNI-5200-60 60 lb 17 in 9.66 in 7.34 in Plastic ball sockets
GSNI-5200-75 75 lb 17 in 9.66 in 7.34 in Plastic ball sockets
Do not choose by pounds alone. The force rating is the spring's push force, not the maximum door weight. An overly strong replacement can stress a compartment lid or hinge; one that is too weak may not hold it safely. Match the original force and mounting geometry.

How to measure a replacement gas spring

  1. Support the hatch or door. Follow JR Products' installation instructions and keep the panel securely held during replacement.
  2. Measure centre to centre. With the spring fully extended, measure the distance between the centres of its end connectors: 17 inches for this family.
  3. Confirm compressed length and stroke. The published compressed length is 9.66 inches, with 7.34 inches of travel. They are not interchangeable with another same-force model of a different length.
  4. Match the force marking. The suffix indicates pounds of force; if the original is marked in newtons, convert or obtain the manufacturer's specified replacement.
  5. Check the installed ends. Plastic sockets with retaining clips must fit the existing ball studs and remain secure through the full door movement.

Installation and safety checks

  • Keep the door safely supported and follow the original installation orientation, with the rod downward in its closed position.
  • For paired installations, replace both springs with correctly matched supports.
  • Inspect ball studs and clips before reassembly. Do not scratch, oil or grease the rod.
  • Make sure the mounted spring does not bottom out before the lid closes, and that the latch opens and closes freely.

Find matching GSNI-${series} supports

These parts are sold online through NewRVParts and ship from supplier warehouses. In-person viewing and pickup are not offered.

If your existing support is a different length, review the 20-inch GSNI-5300 gas spring comparison. For an RV compartment that is difficult to close, see the separate trigger latch comparison before replacing unrelated hardware. JR Products BS1005 10 mm ball stud is separately listed in our store; compare the original stud dimensions and installation before replacing a mounting point.

Bulletin des pièces de VR

Inscrivez-vous pour nos prochaines promotions !

À propos de NewRVParts

NewRVParts est une boutique en ligne spécialisée dans les pièces et accessoires neufs pour véhicules récréatifs, les équipements pour caravanes portées, les pièces de remorquage et de remorques, les accessoires pour camions et les produits nautiques. Nous servons nos clients partout au Canada et aux États-Unis, en expédiant des produits de fabricants de confiance via un vaste réseau de distribution nord-américain. Magasinez en ligne pour obtenir des pièces de rechange, des équipements et des accessoires livrés directement à votre porte.

Magasiner les pièces de VR