Lippert Level Up 14K vs 8K Hydraulic Jack Diagram & Replacement Guide

Compare the original Lippert Level Up 14,000-lb hydraulic jacks with current Gen II replacement families and distinguish them from the separate 8,000-lb mid/rear jack designs. Compare manufacturer jack photographs, mounting-hole patterns and part numbers to identify a replacement. Lead and follow positions, mounting dimensions and hydraulic fittings must match the installed system.

Identification before purchase: Lippert sells different lead and follow Gen II hydraulic jack assemblies. The manufacturer identifies 8005353 as a lead leg and 8005413 as a follow leg, but both current product pages list several of the same earlier MPNs. A supersession list by itself is not enough to choose the correct jack location, hoses or mounting.

Replacement-part photographs and product links

Lippert 8005353 14,000-lb lead-leg hydraulic assembly: existing NewRVParts product photograph800535314,000-lb lead-leg hydraulic assembly14K • Gen IIView exact product Lippert 25712610 Older 14,000-lb clear-anodized hydraulic jack: existing NewRVParts product photograph25712610Older 14,000-lb clear-anodized hydraulic jack14K • legacyView exact product Lippert 433467 Legacy left-side Level Up hydraulic jack: existing NewRVParts product photograph433467Legacy left-side Level Up hydraulic jack14K • legacyView exact product Lippert 433469 Legacy right-side Level Up hydraulic jack: existing NewRVParts product photograph433469Legacy right-side Level Up hydraulic jack14K • legacyView exact product Lippert 19586010 8,000-lb hydraulic jack, early store-listed design: existing NewRVParts product photograph195860108,000-lb hydraulic jack, early store-listed design8K • originalView exact product Lippert 3728923 8,000-lb Gen II silver hydraulic jack: existing NewRVParts product photograph37289238,000-lb Gen II silver hydraulic jack8K • Gen IIView exact product

Lippert factory photographs: distinguish 13-hole and 8-hole 8K jacks

The images below come from Lippert's own annotated manufacturer product illustrations. These photos show two comparison MPNs, 43345810 and 372892—not the silver 3728923 pictured in the NewRVParts product gallery above. Lippert identifies 3728923 as a silver Gen II 8K jack with an eight-hole mounting pattern. Count the holes and confirm the jack's label, stroke, port locations and original mounting hardware before choosing a replacement.

Official Lippert diagram photograph of MPN 43345810 silver 8,000-pound hydraulic jack highlighting its 13 mounting holes and 9-inch footpad
Lippert 43345810 — older silver 8K, 13 holes. Original Lippert annotated product image; comparison reference only. This is not the 3728923 listing.
Official Lippert diagram photograph of MPN 372892 black Gen II 8,000-pound hydraulic jack highlighting its 8 mounting holes and 9-inch footpad
Lippert 372892 — black Gen II 8K, 8 holes. Original Lippert annotated product image. The silver 3728923 also has eight mounting holes per its separate manufacturer specification; colour and MPN differ.

Use Lippert's QR-109 and related jack identification guides to compare mounting-hole patterns and the differences between earlier and Gen II hydraulic jacks. The drawings do not establish that the two generations are interchangeable.

View supplementary simplified 14K versus 8K dimension sketch
Lippert 14K versus 8K hydraulic jack identification diagram Original comparison drawing of a 14,000-lb hydraulic jack cylinder with 20-in stroke, 9-in footpad and bolt-pattern verification; 8,000-lb Gen II jack with 15-in stroke and 9-in footpad; neither is a substitute based on appearance alone. Stylized, not to scale. 14K Gen II8K Gen II 800535320-in factory stroke 372892315-in stroke 9-in footpad 9-in footpad Always compare mounting hole pattern, extended/retracted size, hose ports and exact installed jack code
Simplified comparison of stroke, jack position and footpad size. Refer to Lippert's factory dimensions for mounting or replacement.

Hydraulic jack part-number comparison

Compare the six manufacturer numbers below before selecting a replacement. Pay particular attention to stroke, overall height, mounting position and any differences between the current jack and the original equipment.

Lippert MPN Jack family Product Dimensions and fitment notes
8005353 14K • Gen II 14,000-lb lead-leg hydraulic assembly Lippert identifies a Gen II lead-leg replacement; 20-in stroke and 9-in footpad; its supersession list contains multiple older 14K part numbers.
25712610 14K • legacy Older 14,000-lb clear-anodized hydraulic jack Lippert lists this code among superseded part numbers on newer 14K product pages. Confirm the original plumbing and jack version.
433467 14K • legacy Legacy left-side Level Up hydraulic jack Store describes left-side; newer factory 14K pages include the MPN in supersession lists without proving a universal left/right replacement.
433469 14K • legacy Legacy right-side Level Up hydraulic jack Store describes right-side; confirm the exact original fittings and generation before ordering a successor.
19586010 8K • original 8,000-lb hydraulic jack, early store-listed design Store identifies an original 8K configuration; not a 14K replacement. Verify original mounting-hole pattern.
3728923 8K • Gen II 8,000-lb Gen II silver hydraulic jack Lippert specifies 15-in stroke, 9-in footpad, and 21-1/16-in overall height; 21-1/16 in refers to overall height, not the 15-in stroke; verify both measurements.
Check jack dimensions and package contents: Lippert specifies the 3728923 8K Gen II jack with a 15-in stroke and an approximately 21-1/16-in overall height. The 21-1/16-in overall height is not the same as the 15-in extension stroke. Measure the installed jack and confirm the mounting pattern, hose connections and supplied components before ordering. Check the contents of part 25712610 separately.

Visualize the 14K supersession caution

Show supplementary 14K lead/follow supersession sketch
Lippert hydraulic 14K jack supersession cross-reference caution Historical jack numbers 25712610, 433467, 433469 and 351924 appear in replacement references for 8005353 lead and 8005413 follow assemblies. Confirm the installed leg position and mounting dimensions; the overlapping numbers do not establish interchangeability. Legacy 14K markings25712610433467 (store: left)433469 (store: right)351924 familyRecord original ports and role 8005353 — Gen II lead20-in stroke, 9-in footLippert successor list overlaps legacy codes 8005413 — Gen II follow20-in stroke, 9-in footDifferent part, also with overlapping predecessors No arrow here means direct mechanical fit. Verify factory kit and hose fittings before purchase.
Some older numbers appear on more than one Lippert replacement list. Confirm the lead/follow position, original mounting arrangement and hose fittings before choosing a replacement.

Other factory reference numbers without confirmed store matches

Lippert number Factory reference Why it remains unlinked
8005413 14K Gen II follow-leg assembly Lippert lists a 20-in stroke and 9-in footpad.
2025078919 14K Gen II fitting service kit Lippert lists both 433467 and 433469 as superseded; fitting/service configuration requires separate verification.
351924 / 3519243 Earlier 14K assembly codes Appear on the manufacturer's 8005353 supersession list; determine jack generation and role before ordering.
25712510 Earlier 14K code Listed among 8005353 and 8005413 predecessor codes; identify the original jack before selecting a replacement.
8003503 Previous silver 8K jack code Lippert lists 3728923 as the successor to 8003503. Check original 8K pattern/ports.

What to check on the installed jack

14K legacy vs Gen IIConfirm the original stamped number, mounting-hole pattern, jack stroke, foot diameter, hose port style and whether the replacement is a lead or follow leg. Do not identify the replacement by colour alone.
8K vs 14KThese families are not capacity substitutes. Lippert's 8K Gen II 3728923 factory product describes a 15-in stroke and 9-in footpad; the 14K 8005353 Gen II product describes a 20-in stroke and 9-in footpad.
Hydraulic connectionsDo not infer that elbows, T-fittings or O-ring face seals from one replacement kit are included with another. Confirm the precise kit contents and the factory hydraulic line requirements.
Position and revisionOlder jacks and post-2023 Gen II replacements may use different height or bracket geometry. Follow the Lippert jack comparison and current replacement technical instructions before any chassis work.

Original Lippert model comparison, mounting and replacement references

Lippert QR-109 14K/8K version comparison Lippert QR-088 14K jack identification reference Lippert Level Up owner manuals and service bulletin index Lippert hydraulic landing-gear technical documents

These links open manufacturer technical documentation, not competing shopping pages. The 8005353/8005413 product specifications were cross-checked against Lippert's official product documentation; the original factory sheets govern installation, replacement parts and safety. Hydraulic jacks must never be serviced with pressurized lines or an unsupported coach.

Related NewRVParts leveling references

Ground Control TT Lite electric levelingGround Control 3.0 jack referenceJacks & LevelingRV awning and jack diagrams index

Bulletin des pièces de VR

Inscrivez-vous pour nos prochaines promotions !

À propos de NewRVParts

NewRVParts est une boutique en ligne spécialisée dans les pièces et accessoires neufs pour véhicules récréatifs, les équipements pour caravanes portées, les pièces de remorquage et de remorques, les accessoires pour camions et les produits nautiques. Nous servons nos clients partout au Canada et aux États-Unis, en expédiant des produits de fabricants de confiance via un vaste réseau de distribution nord-américain. Magasinez en ligne pour obtenir des pièces de rechange, des équipements et des accessoires livrés directement à votre porte.

Magasiner les pièces de VR