The Stromberg Carlson CC-275 Bike Bunk raises a 2-inch bike-rack receiver above a travel trailer's A-frame. Use this original parts breakdown to identify the lower mounting pockets, bent support posts, cross tube, frame backers and installation hardware before checking a replacement.

View the complete CC-275 Bike Bunk

Stromberg Carlson CC-275 black steel trailer A-frame Bike Bunk raised receiver assembly
100 lbRack plus bikes combined
14–55 inA-frame mounting width range
6 inMaximum A-frame bar height
2 inBike rack receiver size

Original CC-275 exploded parts and installation drawing

Page 2 of the manufacturer's two-page instructions identifies the nine component groups with callout letters A through I. The mounting sequence and trailer-clearance checks are on page 1.

Open the original CC-275 parts diagram and installation manual (PDF)

On a phone, open the PDF in a separate viewer to enlarge the component labels.

Bike Bunk parts by diagram letter

Callout Manufacturer number Component Quantity
A 7605-104P Lower mounting pockets 2
B 7605-117 Frame backer bars 4
C PST-1895, PST-1865, PST-1860, PST-1870 5/16 × 4 in mounting hardware components 8 bolts, with matching washers and nuts
D 7605-107P Bent vertical support posts 2
E 7605-175 Top cross tube with bike-rack receiver 1
F CP-1075 Cross-tube end caps 2
G FST-1620 1/4 × 3/4 in stop bolts, factory installed 2
H FST-2010 3/8 × 1 in set screws 4
I MPST-2021 / PST-2083 3/8 × 2-3/4 in cross-tube hardware 4

Stromberg Carlson also offers a replacement mounting-hardware assortment as part 2275. The manufacturer lists the four major assemblies separately: 7605-104P lower pocket, 7605-107P bent post, 7605-117P backer bar, and 7605-175 cross tube. The original drawing prints 7605-117 on the backer-bar callout, while the replacement catalog uses 7605-117P.

Dimensions to check on the trailer

Measurement CC-275 dimension
Top of A-frame to top of cross tube 33½ in
Top of A-frame to underside of rack receiver 29 in
Top cross tube length 37½ in
Receiver-tube centre spacing on cross tube 34¼ in
Bent upright tube outside diameter 1.9 in

Confirm the clearance before mounting

The CC-275 is intended to hold an RV-approved bicycle rack, not to tow a trailer or carry other hitch loads. The 100 lb limit includes the weight of the chosen bike rack and all bicycles together. Stromberg Carlson does not approve this mounting system for e-bikes or motorcycles.

Before drilling the uprights, check the tow vehicle's turning clearance with the complete rack and bicycles in place, and allow room to reach propane valves and remove tanks when required. The installation instructions place the frame pockets approximately 2–3 inches from the trailer body, with the upper cross tube about 1–2 inches from it. Confirm the positions on your particular trailer.

Bike rack sold separately. The CC-275 supplies the raised receiver and its mounting structure, not a bicycle rack. Always verify the rack manufacturer's approval for RV/trailer service and its permitted combined load.

For an exterior ladder-mounted bike rack, see the LA-102 bicycle and LA-104 chair rack reference. Browse other illustrated equipment in our RV steps, ladders and accessory parts index.

Boletín de piezas para vehículos recreativos

¡Suscríbase para futuras promociones!

Sobre NewRVParts

NewRVParts es un proveedor exclusivamente en línea de piezas y accesorios nuevos para vehículos recreativos (RV), equipos para autocaravanas, piezas para remolques y enganches, accesorios para camiones y productos marinos. Atendemos a clientes en todo Canadá y Estados Unidos, con productos de fabricantes de confianza enviados a través de una amplia red de distribución norteamericana. Compre en línea repuestos, equipos y accesorios que se entregan directamente en su puerta.

Comprar piezas de RV